At SmartHomePerfected we pride ourselves on providing trustworthy, unbiased information. If you buy through links on our site, we may earn a small affiliate commission at no extra cost to you. Learn more
The use of features like audio alerts, LED notification lights, and visual signals on the touchscreen can greatly assist in overseeing operations and detecting any issues with Kwikset smart locks. However, it's worth mentioning that not all models might have these facilities.
Common signals across different models such as Obsidian, Premis, Halo Touch, Powerbolt 2, and more include …
- Green indicators: Usually signify a successful operation or an unlocked status.
- Amber indicators: Often represent a locked status or a locking action.
- Red indicators: Typically warn of low battery, unsuccessful action, or door jamming issues.
- Blue indicators: Mainly associated with Bluetooth pairing and connectivity.
In this article, I dive into what beeps and lights mean for each Kwikset model.
Show Page Contents
Obsidian
Model
The Kwikset Obsidian smart lock provides a clear and simple set of visual and audio cues to communicate its various status updates and alerts.
For example, the color of the lock status will change depending on whether it's unlocked (blinking green), locked (blinking amber), or has a low battery (blinking red).
Additionally, the display will show an “X” pattern along with beeping to indicate incorrect code entries, a lack of user codes, or when several incorrect codes are entered within a short timeframe.
Each of these alerts is accompanied by easy-to-follow solutions: re-enter the correct code if a mistake was made; program at least one user code if none are present; attempt the programming procedure again if unsuccessful, or wait 60 seconds before re-entering the code after three incorrect attempts.
If the lock emits a long continuous beep while flashing the checkmark and lock symbols, it's time to replace the batteries.
In case the lock beeps continuously, it signifies a disconnection between the interior and exterior components, which requires the removal of the battery pack and reconnecting the two parts before replacing the battery pack.
Finally, if the checkmark and lock symbols alternate flashing along with a long continuous beep, the door might be jammed and would require manual re-locking or repositioning of the strike.
Premis
Model
The Kwikset Premis smart lock uses a combination of lights and sounds to communicate its status to users.
The Status LED, located on the lock's interior, blinks every six seconds to indicate if the door is locked (amber flash), unlocked (green flash), or if the batteries are low (red flash).
Users can disable the LED inside the Premis app if desired.
Additionally, during the pairing process, the LED will flash red and green along with a short beep, unless the lock's sound is muted.
In addition to the Status LED, the Kwikset Premis smart lock also emits audible alerts to inform users of the lock's current status.
These alerts include 1 beep with an X-pattern flash for an incorrect user code, 3 beeps with 3 X-pattern flashes for no user codes programmed or unsuccessful programming, and 15 beeps with 15 X-pattern flashes for 3 incorrect codes entered within a minute.
Moreover, the lock and checkmark symbols flashing simultaneously with a long continuous beep indicate a low battery, while alternating flashes with a long continuous beep signal a door jam.
The lock also features an anti-tampering alarm that continuously beeps when the cable is disconnected.
If this happens, removing the battery pack, reconnecting the cable, and reinstalling the battery pack will resolve the issue.
Users have the option to silence these beeps using the Premis app if they prefer a quieter locking experience.
Halo Touch
Model
When it comes to the Kwikset Halo Touch, understanding the LED indicators is crucial for smooth operation.
The exterior LED indicators provide visual cues for various actions.
An orange sweep occurring towards the door edge signifies locking, followed by all LEDs turning blue when authenticating a fingerprint.
Meanwhile, unlocking is indicated by all LEDs turning orange for 2 seconds, followed by a green sweep moving away from the door edge and all LEDs turning green for another 2 seconds.
If you notice red LEDs, it means that the battery is low or there's a door jam issue.
The interior LED indicators serve a similar purpose, providing important information about different functions.
- A solid green light means the action was successful, while blinking green indicates the lock is unlocked.
- A solid red light indicates door handing was unsuccessful, and a blinking red light signifies either a low battery or an unsuccessful action.
- A solid blue light indicates successful Bluetooth pairing, while blinking blue signals Bluetooth pairing mode.
- A solid orange indicates that the lock is entering network reset mode, and blinking orange means the lock is either locked or in network or system mode.
To identify if your lock's batteries need to be replaced, look for the exterior LED flashing red and beeping after a motorized operation, like locking or unlocking the Halo Touch using a fingerprint.
Powerbolt 2
Model
The Powerbolt 2 smart lock from Kwikset comes with some useful indicators to let you know the status of your lock.
One common issue is when the keypad flashes red three times accompanied by three beeps.
This can mean a few different things, including that the door was jammed while trying to lock, the door handing code has not been entered, no user code is programmed or currently disabled, or that the programming process was unsuccessful.
To resolve these issues, try manually re-locking the door, repositioning the strike, entering the door handing code, programming a user code, or attempting the programming procedure again.
If an incorrect user code was entered, simply re-enter the correct code.
Another set of indicators to be aware of is when the Powerbolt 2 keypad flashes red five or ten times, each accompanied by the same number of beeps.
If the keypad flashes red five times and emits five beeps, this means that five incorrect User Codes were entered within a minute.
Wait for a 45-second keypad lockout period before trying to enter the code again.
On the other hand, if the keypad flashes red ten times and beeps ten times, this indicates that your lock's batteries are running low.
To resolve this, simply replace the batteries to ensure your smart lock continues to function effectively.
Kevo Convert
Model
Kevo Convert is a simple and user-friendly smart lock solution designed by Kwikset.
It allows homeowners to remotely lock and unlock their door without having to worry about the hassles of keys.
With the Kevo Convert, understanding the lock’s status is quite straightforward thanks to the helpful flashing lights.
These colored indicators will keep users aware of what is going on with their lock.
When the Kevo Convert flashes amber, it indicates that the door is securely locked.
If a green flash is observed, it means that the door has been successfully unlocked.
It is essential for users to keep an eye out for a red flash, as this is a warning that the four AA batteries powering the Kevo interior are low and require replacement.
Staying informed about these visual indicators will help users efficiently manage their smart lock system and maintain the best security possible for their home.
Kevo
Model
Kwikset's Kevo Smart Lock utilizes a series of beeps and flashes to help users understand the lock status and diagnose potential issues.
- A blue spinning light followed by shut off indicates that Kevo could not establish a connection with your device, or it detected the device inside.
- A magenta flash signifies that your device is outside the activation range and requires the lock's inside-outside sensor to calibrate to the new location.
- Red flashes mean the lock has detected an unauthorized device within range, preventing the lock from unlocking.
- Solid red LEDs at the top signify that the AA batteries need to be replaced, while a solid red LED at the bottom means that the fob battery needs replacement.
- Red flashing side LEDs indicate a jammed deadbolt, requiring a check on door alignment and latch bolt operation.
SmartCode 913
Model
The SmartCode 913 by Kwikset is an innovative smart lock that comes with several beeping and flashing signals to communicate different statuses for the user.
- When the Status LED blinks green, it indicates the lock is unlocked.
- If it's blinking amber, the lock is secured.
- A blinking red Status LED means the battery is low and requires a replacement soon.
- In some cases, when the Status LED is solid red, it implies the door handing process hasn't been done correctly. This could be due to various factors such as the lock's interior not being perpendicular to the ground, misaligned door hole or latch, low battery level, or an upside-down installed latch for the model 910.
The SmartCode 913 keypad also provides essential information through beeping and flashing.
- Red flashing accompanied by three beeps signals that there's no programmed user code, the wrong code was used or there was an unsuccessful programming attempt.
- Another situation is when the keypad flashes red for 15 times with 15 beeps, which indicates three consecutive incorrect codes entered, leading to a 60-second keypad lockout.
- During low battery conditions, the keypad will flash red 10 times with 10 beeps as a reminder for battery replacement.
- A green-flashing keypad with a continuous beeping sound for two seconds highlights a jammed deadbolt in the locked position; in this case, try to relock the door manually and reposition the strike if necessary.
- Lastly, red flashing with continuous beeping for two seconds indicates a jammed deadbolt in the unlocked position; manually relock the door and reposition the strike as required.
SmartCode 914
Model
This is the same as the SmartCode 913 above with the following exception.
- A single red flash accompanied by one beep means an incorrect code was entered, prompting you to try again.
- Three red flashes with three beeps imply that no user code is programmed or there was an unsuccessful programming attempt.
SmartCode 260
Model
The Kwikset SmartCode 260 lock provides visual and audible cues to help users understand its current status and any issues that may arise.
When unlocking the device, two green flashes with two beeps signify a successful unlock.
However, if you see ten red flashes along with ten beeps, the lock's battery is low and needs replacing.
In case you input an incorrect user code, you will notice three red flashes accompanied by three beeps.
If there are over three incorrect attempts made, fifteen red flashes and fifteen beeps occur, prompting the user to wait one minute before trying again.
On the other hand, locking the device brings forth its own set of signals.
Two amber flashes and two beeps denote a successful lock.
A low battery, once again, is indicated by ten red flashes and ten beeps.
If the bolt is stuck or jammed, the lock will alternate red and white flashes while emitting five beeps.
Factory reset and programming also have corresponding visual and auditory cues; a successful factory reset or programming will flash green once and beep once, whereas unsuccessful attempts will result in three red flashes and three beeps.
In such cases, review the steps and retry the process.
275 Touchscreen Electronic Deadbolt
Model
The Kwikset 275 Touchscreen Electronic Deadbolt is designed to provide its users with a secure and convenient home access system.
This smart lock has various beeps and flashes to indicate different functions and statuses.
For instance, a single beep signifies a successful operation – this could be successfully locking or unlocking the door.
Meanwhile, two beeps indicate that the lock's programming has been completed.
This commonly occurs while adding, modifying, or deleting user codes.
On the other hand, three beeps indicate an operation error, which could result from an incorrect user code or a malfunction.
If five incorrect user codes are entered consecutively within one minute, the lock emits five beeps and flashes an X-pattern (1-3-5-7-9).
In such cases, the touchscreen goes into a lockout mode for 45 seconds before allowing re-entry of the code.
Moreover, if the lock emits 10 rapid beeps, this signals a low battery and a need for replacement.
Three long beeps convey that the lock's default settings have been restored.
Lastly, if the lock button flashes slowly, it signifies that the lock is in programming mode, allowing the user to modify settings, such as adding or deleting user codes.
Overall, these beeps and flashes are essential in understanding the smart lock's performance and any potential issues that may arise.
SmartCode 888
Model
SmartCode 888 is a popular smart lock with a variety of features, including status LED notifications.
To enable or disable the status LED, you can follow these steps:
- First, press the Program button once.
- Then, press button “A” once.
- After that, you can press button “1-2” multiple times if needed to reach the desired state.
- When you see the green Lock button, it means the feature is enabled; the red Lock button signifies the feature is disabled.
The Status LED on the SmartCode 888 can display several colors and patterns to communicate different lock statuses.
- When the LED blinks green, your lock is unlocked; blinking amber means it's locked.
- If the LED blinks red, you have a low battery.
- A solid red LED indicates the door handing process didn't work properly, which could be due to misaligned parts, low battery, or other issues.
- The keypad's red flashes and beeps provide additional information, such as incorrect code entries, programming issues, or low battery warnings.
- For example, if the keypad flashes red 15 times with 15 beeps, you've entered three consecutive incorrect codes, and your keypad will lock out for 60 seconds.
Aura
Model
Kwikset's Aura Smart Lock communicates various lock statuses and actions to users through a series of LED colors and beeping alerts.
- A solid green light indicates that an action has been successful, while a blinking green light means the lock is unlocked.
- A solid red light signals an unsuccessful door handing process or an incomplete action.
- When the red light is blinking, the lock's battery is running low.
- In cases where the blue light is solid, the Bluetooth pairing has been successful.
- Meanwhile, a blinking blue light shows that the lock is in Bluetooth pairing mode.
- Amber lights on the Aura Smart Lock have two purposes. A solid amber light means the lock is entering Network Reset mode, while a blinking amber light indicates that action is required, such as placing the lock into Network or System Reset mode.
Adjusting the LED notification settings or programming features is possible through various smart home applications that are compatible with Kwikset's smart lock technology.
SmartCode 910
Model
The Kwikset SmartCode 910 lock communicates various conditions through a combination of beeps and colored flashes on the keypad.
- When the keypad flashes red once, accompanied by a single beep, it indicates that the door jammed while trying to lock. To resolve this issue, manually re-lock the door and, if necessary, reposition the strike.
- If a series of three red flashes and three beeps occur, it means that either programming was unsuccessful, an incorrect code was entered, or that no user codes have been programmed. Attempt the programming procedure again, ensure the correct code is entered, or program at least one user code to fix this.
Red flashes and beeps in other patterns provide additional information about the lock's status.
- A sequence of ten red flashes with ten beeps warns of low battery, signaling that it is time for a replacement.
- When the lock beeps twice, and the keypad flashes red three times followed by six red flashes with six beeps, it indicates a programming timeout. In this case, try the programming procedure once more, making sure not to pause for more than five seconds throughout the process.
- If the keypad flashes red 15 times with 15 corresponding beeps, it means that three incorrect codes were entered within a minute. Re-enter the correct code after waiting for the 60-second keypad lockout.
The lock's status can also be identified through continuous color flashes: blinking green indicates the lock is unlocked, blinking amber means it's locked, and blinking red warns of a low battery.
A solid red flash signifies an issue with the door handing process.
Conclusion
In conclusion, Kwikset smart locks utilize an assortment of beeps, screen flashes (for models with a touchscreen), and LED indicators to help users understand their lock's status, diagnose issues, and maintain optimal performance.
By understanding these signals, you’ll be able to efficiently manage and troubleshoot your Kwikset smart lock.
Sources
- https://kwiksetprodstorage.blob.core.windows.net/documents/kw_tg_5049707_910.pdf
- https://kwiksetprodstorage.blob.core.windows.net/documents/kw_tg_5061920_913.pdf
- https://kwiksetprodstorage.blob.core.windows.net/documents/kw_tg_5061899_888.pdf
- https://kwiksetprodstorage.blob.core.windows.net/documents/kw_is_5066070_919.pdf
- https://kwiksetprodstorage.blob.core.windows.net/documents/kw_ig_5052436_260[cnt].pdf
